سرفصل دوره MTVUME میکروتیک

• PPP
• PPP Profile
  • Local and remote addresses
  • Incoming and outgoing filters
  • Address list
  • Change TCP-MSS
  • Use encryption
  • Session timeout
  • Rate-limit configuration
  • Only-one setting
• PPP Secret
• Service and Profile
• Local and Remote address
• Routes configuration
• Limit Bytes In/Limit Bytes Out configuration

• IP Pool
• Set addresses ranges 
• Set addresses ranges
• Next pool option
• Module 1 laborator

• PPTP, LT2P
• • PPTP and L2TP
  • Theory
  • Comparison
  • PPTP Client configuration
  • Client setup
  • Set profile
  • Dial on demand
  • Add default route and static routes
  • PPTP Server configuration
    • Enable server
    • Setup profiles
    • Add clients to PPP secret
    • Set static interfaces for clients
  • L2TP Client configuration
  • Client setup
  • Configure profile
  • Dial on demand
  • Add default route and static routes
  • L2TP Server configuration
  • Enable server
  • Set profiles
  • Add clients to PPP secret
  • Set Static interfaces for clients

• Module 2 laboratory

• PPPoE
• PPPoE server and client
• Theory
• Usage environment
• Comparison to other PPP protocols
• PPPoE client configuration
• Client setup
• Select interface
• Service name
• Configure profile
• PPPoE Server configuration
• Enable PPPoE server
• Set profiles
• Add clients to PPP secret
• Add Static interfaces for clients
• Secure server by removing any IP address from PPPoE server interface
• Encryption
• Set profile without encryption
• Set profile with encryption
• Configure PPPoE client without encryption
• Interface ECMP
• Set ECMP routes for PPP interfaces
• Module 3 laboratory

• Bridging
  • L2TP and EoIP
    • Set L2TP tunnel
    • Set EoIP tunnel
    • Create bridge and add necessary interfaces to ports
    • Confirm you have Ethernet connectivity between remote nodes
  • L2TP and VPLS
    • Set L2TP tunnel
    • Set VPLS tunnel
    • Create bridge and add necessary interfaces to ports
  • L2TP and BCP
    • Set L2TP tunnel
    • Use BCP to bridge PPP interface
    • Add to bridge necessary interface
  • Multilink Protocol
    • Enable multilink by specifying correct MRRU settings
    • Disable mangle rules for MSS adjustment
  • MLPPP (optional)
    • Setup client and specify multiple interfaces for one client
    • Set PPPoE server with MLPPP support
  • Module 4 laboratory

• IPSec
  • Introduction
  • Theory and concepts
  • Comparison to other VPN protocols
  • IPSec Peer
  • Use different authentication methods
  • IPSec exchange modes
  • Encryption and hash algorithms
  • NAT-Traversal
  • Lifetime and lifebytes
  • DPD protocol
  • Policy
  • IPSec protocol and action
  • Tunnels
  • Generate dynamic Policy
  • Proposal
  • Encryption and authentication algorithms
  • Lifetime
  • PFS
  • Installed-SA
  • Flush SA
  • Create IPSec between two routers with NAT
  • Set peer
  • Set policy
  • Set NAT rules
  • Confirm the secure link is established
  • Module 5 laboratory

• HotSpot
  • Introduction
• Concepts
• Usage environments
• Setup HotSpot with default settings
  • HotSpot Login Methods
  • HTTP CHAP/PAP
  • MAC
  • Cookie
  • HTTPS
  • Trial
  • RADIUS
    • Users
    • Add users
    • Set MAC-address for user
    • Set MAC-address for username
    • Limit Uptime and Limit Bytes In/Out
    • Reset limits for user
      • Monitor Users
      • Host Table
      • Active Table
      • SNMP for users
        • Profile
          • Keepalive timeout
          • Shared users
          • Rate-Limit
          • Address-list
          • Incoming/Outgoing filter
          • Incoming/Outgoing Packet Mark
          • Bypass HotSpot
            • Walled garden
            • Walled garden IP
            • IP binding
            • Customize HotSpot
              • Advertisement
              • Customize pages
              • Module 6 laboratory

• RADIUS
  • RADIUS client
    • Add radius client
    • Set service
    • Use RADIUS for the specific service
    • RADIUS server
    • User manager
      • Install the latest user-manager
      • Add routers
      • Add users
      • Set profile
      • RADIUS incoming
      • Module 7 laboratory